全guo免费招商热线: 400-800-4491
产品咨询订购电话: 134-1834-4523
 dang前位置:模具防锈剂shouye - xin闻动tai - 技shufenxiang - 模具维修

永利会永利会

发bu时间:2016.09.24 xin闻来源:脱模剂_防锈剂_清洗剂_顶针you_深chou澳门永利集团精xi科技有xian公司

模具述语

一、入shui:gate

进入位: gate location

shui口形式:gate type

大shui口:edge gate

xishui口: pin-point gate

shui口大小:gate size

转shui口: switching runner/gate

唧嘴口jing: sprue diameter

二、流道: runner

热流道: hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道:round(full/half runner

流道电脑fenxi:mold flow analysis

流道苆iao狷runner balance

热嘴: hot sprue

热流道板:hot manifold

发热管:cartridge heater

探针: thermocouples

插头: connector plug

插座: connector socket

密封/封liao: seal

三、运shui:water line

喉塞:line lpug

喉管:tube

sujiao管:plastic tube

快速統ou罚簀iffy quick connector plug/socker

四、模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

边ding/导边:leader pin/guide pin

边司/导套:bushing/guide bushing

中托司:shoulder guide bushing

中托边L:guide pin

顶针板:ejector retainner plate

托板: support plate

螺丝: screw

管ding:dowel pin

开模槽:ply bar scot

内模管位:core/cavity inter-lock

顶针: ejector pin

司筒:ejector sleeve

司筒针:ejector pin

推板:stripper plate

缩呵:movable core,return core core puller

扣机(尼龙拉勾):nylon latch lock

斜顶:lifter

模胚(架): mold base

上内模:cavity insert

下内模:core insert

行位(滑块): slide

xiang件:insert

压座/斜鸡:wedge

耐mo板/you板:wedge wear plate

压条:plate

撑头: support pillar

唧嘴: sprue bushing

挡板:stop plate

定位quan:locating ring

锁扣:latch

扣鸡:parting lock set

推杆:push bar

栓da螺丝:S.H.S.B

顶板:eracuretun

huo动臂:lever arm

fen流zhui:spure sperader

shui口司:bush

la圾ding:stop pin

隔片:buffle

弹弓柱:spring rod

弹弓:die spring

中托司:ejector guide bush

中托边:ejector guide pin

xiang针:pin

销子:dowel pin

波子弹弓:ball catch

喉塞: pipe plug

锁模块:lock plate

斜顶:angle from pin

斜顶杆:angle ejector rod

尼龙拉勾:parting locks

huo动臂:lever arm

复位jian、提前回杆:early return bar

气阀:valves

斜导边:angle pin

shu语:terms

承压平mian苆iao猓簆arting surface support balance

模pai气:parting line venting

回针碰liao位:return pin and cavity interference

模zong高超chupi机规ge:mold base shut hight

顶针碰运shui:water line interferes withejector pin

liao位chu上/下模:part from cavith (core)side

模胚yuanshenchuliao位:cavity direct cut on A-plate,core direct cut on B-plate.

不zhun用xiang件: Do not use (core/cavity) insert

用铍铜做xiang件: use beryllium copper insert

初步(正式)模tu设计:preliinary (final) mold design

反呵:reverse core

弹弓压缩量:spring compressed length

稳定xing好:good stability,stable

强度不gou:insufficient rigidity

jun匀冷却:even cooling

扣模:sticking

热peng胀:thero expansion

公cha:tolorance

铜公(电极):copper electrode



Tags: suliao 模具 ying语 脱模剂